Manual_TTI_TCB-881_Multi.pdf

《Manual_TTI_TCB-881_Multi.pdf》由会员分享，可在线阅读，更多相关《Manual_TTI_TCB-881_Multi.pdf（132页珍藏版）》请在收音机爱好者资料库上搜索。

1、4W MOBILE CBTRANSCEIVER INSTRUCTIONMANUAL www.ttikorea.co.kr Downloaded from www.cbradio.nl CONTENTS 3 3 3 6 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 11 12 12 13 14 15 15 16 17 18 19 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11) 12) 13) 14) 15) 16) 17) 18) 19) 20) 21) 6 6 7 8 8 8 9 9 9 9 10 10 10 10

2、10 10 10 11 11 11 11 Introduction Supplied Accessories Installation Transceiver Controls and Functions LCD Display Microphone Menu Setting Mode How to Operate theTransceiver Band Selection Trouble Shooting CE Declaration Safety Requirement Specification Restrictions on the use FreequencyTable Channe

3、l Selector DualWatch Memory Channel Selectors Emergency Button LCD Display Scan/Lock Button AM/FM and LCR Button CB/PA Selector ANL/OFF Selector Local/DX selector Volume and Power On/Off Knob Quick Up/Quick Down Selector Microphone Gain Knob RF Gain Knob Squelch Control knob Microphone Jack Antenna

4、Connector S-Meter PA Jack EXT Jack Power 13.8V DC ENGLISH ENGLISH 1.Introduction 1 unit 1 unit 1 unit 1 unit 2 pieces 3 pieces 2 pieces 1 piece TCB-881 transceiver is designed to have a good performance in any conditions that the transceiver operates,using rugged build chassis,PCBs and components.Th

5、is transceiver is also designed for usersconvenience,implementing human ergono- mics to locate the knobs and buttons in the proper places.The combination of well designed knobs and buttons as well as user friendly graphic layouts will lead users to quickly adapt themsel- ves for the easy operation.T

6、he newly applied menu mode will make professional users more satisfactory with pleasure.The elegant and luxury blue LED light supporting the face design will go well with any vehicles. This instruction manual has been designed to enable you to get the best use from your CBTransceiver,therefore you a

7、re reco- mmended to take a few minutes to read this instruction manual before initial use of your CBTransceiver. Your transceiver is supplied with a full range of accessories to help you get started and virtually benefit from all the features straight away. TCB-881 transceiver Microphone with cord P

8、ower cable Radio mounting bracket Radio mounting thumb screw with rubber washer Mounting screw with washer (for transceiver bracket) Mounting screw with washer (for microphone bracket) Microphone mounting bracket 2.Supplied Accessories Plan the location of the transceiver and microphone first,which

9、is most convenient for the operation.The transceiver should normally be mounted horizontally,but may be mounted vertically.The bracket supplied can be fitted above or below the case allowing theTCB-881 to be cradled by the bracket or suspended from it. 3.Installation 3TCB-881 Consider that this loca

10、tion of the transceiver should not interfere with the driver and passengers.Choose a spot where the microphone and all controls are easily accessible. 1) Put the mounting bracket on the proper location where you are going to install. 2) Drill holes and fix mounting bracket on the location. 3) Connec

11、t the antenna cable plug to the standard receptacle on the transceiver,which is marked ANT. 4) Connect the power cable directly to the vehicle battery or fuse box of the car.Be careful to make sure of the polarity of the battery first and connect the cable.(Red:Positive Pole(+), Black:Negative Pole(

12、-).The same colours are shown on the battery and in the fuse box of the car.) 5) Connect the power cable to the transceiver cable. 6) Mount the microphone bracket on one side of the transceiver, or near it using two screws included. 7) Connect the microphone to the transceivers microphone receptacle

13、.Now you are ready to operate the transceiver. ENGLISH 4TCB-881 ENGLISH It is very important to select a good quality high efficiency 27MHz antenna.A poor quality antenna or one not designed for the 27MHz band will give very poor performance and could cause damage to the transceiver. 1) Place the an

14、tenna as high as possible. 2)The longer the antenna is,normally the better is the performance of the transceiver. 3)Try to mount the antenna in the centre of the surface that you select. 4) Make sure that you have a solid metal?to?metal ground connection. 5) Be careful not to damage the cable during

15、 the installation. Installing An Antenna Warning :Never try the operation of your transceiver before connecting a proper antenna in order not to cause any damage. 5TCB?881 4.Transceiver Controls and Functions 1) Channel Selector Turn right or left,and this allows you to select the channel one by one

16、 that you like to use. 2) DualWatch Press momentarily this button,and this allows you to monitor two channels that you pre-selected and memorized.You may select the emergency channel.To stop this function,press momentarily again this button. 1 151416111312 7891035264 17 18 1920 21 ENGLISH 6TCB-881 E

17、NGLISH 3) Memory Channel Selectors Momentary press allows you to directly access the pre-memorized channels (Memory Recall). The LCD displays one of the memory number icons (M1,M2,M3 and M4). To set the dual watch for the first time,press this button momentarily while you are on the current (primary

18、) channel. The DW icon will be blinking. Select another channel that you like to use as sub-channel (se- condary channel) during the icons blinking using the channel selector or quick up/quick down selector.Press this button momentarily again to activate the dual watch.The icon stops blinking and ke

19、eps being displayed.The dual watch starts. To memorize channels (Memory Store),first select the channel that you are going to memorize and press one of the memory channel selectors for more than 3 seconds.This will make the channel memorized and at the same time the transceiver starts to operate on

20、the same channel. To return to the previous channel operation,momentarily press the memory channel selector,or use the channel selector or quick up/quick down selector. When you select a channel and the channel is same as one of the memorized channels,the matching memory number icon blinks. To chang

21、e the dual watch channels,press the DW button during dual watch operation.The dual watch stops. If you press the PTT button whilst receiving a signal in dual watch mode the transceiver will transmit on the currently displayed channel.If you press the PTT button when no signal is present the transcei

22、ver will transmit on the primary channel. Emergency Scan :Press dual watch button for about two (2) seconds.The transceiver starts the emergency scanning.The transceiver visits the emergency channel once in every second during this scanning.Press the scan button to deactivate this scanning. 7TCB-881

23、 4) Emergency Button Pressing this button will lead you to the emergency channel,CH 9 and the EMG icon will be displayed.The channel selector,quick up/quick down selector and any memory channel selectors will not work. To return to the previous operation mode, momentarily press the emergency button

24、again. 5) LCD Display Most of the operational information is displayed. Please see item no.5 for the details of information. 6) Scan/Lock Button Scan :Press this button momentarily to start scanning upward to catch any channels that are occupied by others. To activate/deactivate the channel scan,pre

25、ss the Scan button briefly.The Scan icon will appear when the channel scan is active.Scanning will only stop when you deactivate the scan function. Turn the channel selector counter-clockwise during scanning in order to change the scanning direction. The transceiver will scan through the whole trans

26、ceiver channels.If your transceiver detects a valid signal the scan will pause for the period that has been set by the menu mode setting (continuously receiving or 1-99 seconds for scan receive time and immediate response or 1-99 seconds for scan delay time). If you press the PTT button when your tr

27、ansceiver detects a signal,the radio will transmit on the same channel.Scanning will resume after the scan receive time and/or the scan delay time.Use the channel selector or quick up/quick down selector to resume scanning immediately. ENGLISH 8TCB-881 ENGLISH 7) AM/FM and LCR Button When the transc

28、eiver is used in UK,UE,or EC freequency band modes this button activates or deactivates Last Channel Recall function.In all other modes (where national regulations permit this),this button allows user to switch between AM and FM modes by momentarily pressing this button. 8) CB/PA Selector This selec

29、tor should be on CB location in order to operate the CB transceiver.To make a public announcement,the PA can be selected.In this case only the PTT button works and you can speak through the PA speakers. 9) ANL/OFF Selector By selecting the ANL location,the transceiver can reduce such impulsive noise

30、 as generated by engine of your vehicle or external sources.This works only when the transceiver is in AM mode. 10) Local/DX selector To receive weak signals,locate the selector on the DX position.While the transceiver is in the location where the signal is very strong,location the selector on the L

31、ocal position.This gives attenuation to get better audio sound. Lock :Press this button for more than 2 seconds to activate and deactivate the keypad lock function.This function locks only the channel selector,quick up/quick down buttons,AM/FM button and scan button.Other buttons and selectors work

32、normal. If you press the PTT button during scanning,the radio will return to your original channel.Scanning will resume after the scan receive time and/or the scan delay time.Use the channel selector or quick up/quick down selector to resume scanning immediately. 9TCB-881 12) Quick Up/Quick Down Sel

33、ector 13) Microphone Gain Knob 14) RF Gain Knob Turn this knob clockwise until you get better RF gain.You may need to decrease the sensitivity by turning the knob counter-clockwise when there is a very strong signal. 15) Squelch Control knob 16) Microphone Jack Insert the microphone into this jack.U

34、se the guide for easy connection. 11)Volume and Power On/Off Knob ENGLISH 10TCB-881 To switch on the transceiver turn this knob clockwise. After clicking sound the transceiver is switched on.The more you turn this knob clockwise,the bigger the audio sound grows. Turn this selector clockwise to incre

35、ase channel numbers by 10 steps.Turning this selector counter -clockwise reduces the channels by 10 steps. Turn this knob clockwise and counter-clock until you get better microphone gain while you move the microphone to the optimum distance from your mouth. MainSquelchControl:Turn this knob counter-

36、clockwise until you hear the background noise and then turn the knob a little clockwise until the noise disappears.In this way,you get the best receive sensitivity. DSS: If you like to use the DSS(Dynamic Squelch System),turn this knob counter clockwise until hearing the click sound.To return to the

37、 manual squelch turn this knob clockwise until hearing the click sound and then follow the manual squelch setting procedure. ENGLISH 19) PA Jack Connect a loud speaker to use this transceiver as an audio amplifier. 20) EXT Jack Connecting a loud speaker to this port makes the built-in speaker turned

38、 off. 21) Power 12V/24 DC Connect the power supply cable to this port. 5.LCD Display 1 2 3 4 5 6 7 8 9 10 11 12 13 Selected Frequency Band Low Power (AM 1Watt) Scan Transmit FM Mode AM Mode Channel Display Signal Strength Meter Memory Channel Activated Receive DualWatch Mode Keypad Lock Emergency Ch

39、annel Display 123457 12119 108 6 13 18) S-Meter Connect an external S-Meter (This is not supplied.) to this port. 11TCB-881 17) Antenna Connector Insert the mail connector of the antenna cable into this female antenna connector. Note : This transceiver works most properly at 13.2V DC input.And one h

40、igh voltage protection circuit is installed to protect this transceiver from 24V DC connection. 6.Microphone 7.Menu Setting Mode 1 Up Button :Use this button to change the channels upward. 2 Down Button :Use this button to change the channels downward. 4 PTT Button :While pressing this button,you ca

41、n transmit. 5 6 Pin Microphone Connector : Connect this to the microphone jack on the front panel of the transceiver. 3 Lock Button :This locks the up button and down button of the microphone. Also,this lock works same as the lock button on the transceiver front panel. On() / Off() High() / Low() /

42、Off() Off() and 199 Sec. Continue() and 1-99 Sec. Off() and 199 Sec. BeepTone Backlight Dimmer Scan DelayTimer (after Receiving signal) Scan ReceiveTimer Time-outTimer Pressing the Lock button of the microphone,turn on the transceiver.The transceiver goes to the Menu Setting Mode, which has the foll

43、owing menu features.This menu setting mode allows you to program user preferences,activate features and use advanced functions. DisplaySettingsFunctions 2 3 4 5 1 ENGLISH 12TCB-881 ENGLISH Note : 1.Use Channel Selector to selecte the main menu features such as BeepTone,Time-outTimer,Scan ReceiveTime

44、r, Scan DelayTimer,Backlight Dimmer and BacklightTimer. 2.Use AM/FM button to enter value setting level. 3.Use Channel Selector to select or change any value that you like to have while the values are blinking. 4.Use SCAN button to return to the previous main menu features. 5.Press Lock button or PT

45、T button of the Microphone to complete the selections and changes and return to the stand-by mode.Or the selections and changes will be automatically confirmed after 5 seconds of the selections and changes.Using Scan button to return to the previous main menu features will be accompanied by the auto

46、matic confirmation of the selected values and changes. 8.How to Operate theTransceiver 1) Make sure the microphone is connected to the microphone jack. 2) Make sure the power cable is connected properly. 3) Make sure the antenna is connected to the antenna receptacle. 4) It is better to put the sque

47、lch control knob turned fully counter-clockwise. 5)Turn on the transceiver and control the volume level. 6) Adjust the squelch control knob to the optimum level. 7) Select your desired channel. 8)To transmit,press the PTT button and speak to the microphone. 9) Release the PTT button to receive. 13TC

48、B-881 9.Band Selection Pressing AM/FM button and Scan button at the same time,turn on the transceiver.Using the channel selector,select the band that you are going to select.The LCD display offers you the band information.The band chart for each area is as follows. Press AM/FM button while the band

49、information is blinking or wait for 5 seconds to complete the selection and go to the transmit and receive mode.This transceiver has EC band setting when it is shipped out from the factory. UE (EU/UK) I I2 D D2 EU EC E F PL UK DisplaySettingsBand Europe 40 Ch FM 4W Spain 40 Ch AM/FM 4W France 40 Ch FM 4W,40 Ch AM 1W UK 40 Ch FM 4W (British Frequencies) Italy 40 Ch AM / FM 4W Italy 34 Ch AM / FM 4W Germany 80 Ch FM 4W,12 Ch AM 1W Germany 40 Ch FM 4W,12 Ch AM 1W Europe 40 Ch FM 4W,40 Ch AM 1W UK 40 Ch FM 4W (British Frequencies) + CEPT 40 Ch FM 4W (EC) Poland 40 Ch AM / FM 4W (Polis