Line_6_Software_Reset_Procedures电路图.pdf

《Line_6_Software_Reset_Procedures电路图.pdf》由会员分享，可在线阅读，更多相关《Line_6_Software_Reset_Procedures电路图.pdf（2页珍藏版）》请在收音机爱好者资料库上搜索。

1、 6033 De Soto Ave. Woodland Hills, CA 91367 P. 818-575-3600 F. 818-676-1585 E. Hard Reset Procedures 1. PODPower up while holding the up and down arrow 2. FlextonePower up holding ABCD buttons 3. SpiderHold A while powering up 4. AX2Hold User/preset and save while powering up 5. Modeler pedalsHold f

2、irst and fourth while powering up 6. AxSysHold user preset/store while powering up 7. Studio Modelers - Power unit up while holding down the MIDI/SYS button and then release. Press and release MIDI/Sys to execute INIT. 8.Vetta Hit Save button, scroll to appropriate reset page (Factory or User from b

3、ack up memory) 9. POD XT / POD XT Pro - Press SAVE button and scroll the “SELECT” encoder clockwise until you reach “Factory Recall” page. Hit Save button a second time. 10. Flextone 3 / Duoverb Power up while holding A and D buttons down. Procedure for finding Firmware versions 1. PODpower up holdi

4、ng the manual button. (LED Display will read out full number.) 2. Flextone-Power up holding down “C” button. “D” button will flash for major version; “Save” button will flash for minor version. Example: For Flextone 2.1 software the “D” button will flash 2 times and then the “Save” button will flash

5、 once. 3. Spider- Power up holding down “B” button. The display will show the following info for approximately 2 seconds: Version 1.1 = “Clean” and “D” LEDs will light up. Version 1.2 = “Clean” and “C” LEDs will light up. RadioFans.CN 收音机爱 好者资料库 Version 1.3 = “Clean”, “C” and “D” LEDs will light up.

6、 The MAJOR VERSION will be displayed on the Amp Select LEDs. Version 1 = CLEAN LED; Version 2 = BLUES LED Version 6 = SCREAM LED The MINOR VERSION (0 - 15) will be displayed on the Channel LEDs in binary form. The LS bit is right justified. If this is a BETA VERSION, the Tape Echo LED will light. 4.

7、 AX2/Axsys While amp is on, hold down the top (“Aux/Midi”) and bottom (“Main”) function buttons simultaneously. The software version will be displayed in the LED display. 5. Modeler pedals -Hold down far right button while powering unit up. Far left LED will flash for the MAJOR version; second LED f

8、rom left will flash for minor version. Example: Version 1.2 = Far left LED will flash once, second LED from left will flash twice. 6. Studio Modelers - Power unit up while holding down the BYPASS button and then release. The display will now read V1.0 x designating the current software version. 7. V

9、etta - Press System Setup and turn the PAGE knob clockwise to the last page. The right display should read “V e t t a Version 1.0 x”, denoting the current software version.) 8. POD XT/POD XT Pro press TUNER button. Scroll SELECT encoder clockwise to the last page to see Firmware version number. 9. F

10、lextone 3 / Duoverb - Power unit up while holding down the Channel C button. Count the number of times the B, C, and D buttons flash. The B button represents the MAJOR version, C represents the first decimal in a point release and D represents the second. So one B flash, one C flash and 2 D flashes will indicate firmware release 1.12. RadioFans.CN 收音机爱 好者资料库