Pioneer-DDJRZX-mix-sm电路图 维修手册.pdf

《Pioneer-DDJRZX-mix-sm电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Pioneer-DDJRZX-mix-sm电路图 维修手册.pdf（103页珍藏版）》请在收音机爱好者资料库上搜索。

1、ORDER NO. 6F, Yokohama i-Mark Place, 4-4-5 Minatomirai, Nishi-ku, Yokohama, Kanagawa 220-0012 JAPAN 2016 Pioneer DJ Corporation 2016 DDJ-RZX RRV4653 DJ Controller DDJ-RZX THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S). THIS SERVICE MANUAL SHOULD BE USED TOGETHER WITH THE FOLLOWING M

2、ANUAL(S). ModelTypePower RequirementRemarks DDJ-RZXLWSYXJAC 110 V to 240 V DDJ-RZXUXJCBAC 110 V to 240 V DDJ-RZXXJCNAC 220 V ModelOrder No.Remarks DDJ-RZXRRV4654SCHEMATIC DIAGRAM, PCB CONNECTION DIAGRAM, PCB PARTS LIST K-ZZZ JUNE RadioFans.CN 收音机爱 好者资料库 2DDJ-RZX 1234 A B C D E F 1234 SAFETY INFORMAT

3、ION WARNING This product may contain a chemical known to the State of California to cause cancer, or birth defects or other reproductive harm. Health it is not meant for the casual do-it- yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly

4、 and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely, you should not risk try

5、ing to do so and refer the repair to a qualified service technician. RadioFans.CN 收音机爱 好者资料库 3DDJ-RZX 5678 5678 A B C D E F CONTENTS SAFETY INFORMATION.2 1. SERVICE PRECAUTIONS.4 1.1 NOTES ON SOLDERING.4 1.2 NOTES ON PARTS REPLACEMENT.4 1.3 SERVICE NOTICE.5 2. SPECIFICATIONS.7 3. BASIC ITEMS FOR SER

6、VICE .8 3.1 CHECK POINTS AFTER SERVICING .8 3.2 JIGS LIST.8 3.3 PCB LOCATIONS.9 4. BLOCK DIAGRAM .11 4.1 OVERALL CONNECTION DIAGRAM.11 4.2 OVERALL BLOCK DIAGRAM.12 4.3 POWER BLOCK DIAGRAM .15 4.4 MATRIX TABLE.16 5. DIAGNOSIS .19 5.1 POWER ON SEQUENCE.19 5.2 TROUBLESHOOTING.22 5.3 MONITORING OF POWER

7、 SUPPLY AND VOLTAGE.38 5.4 OPERATION CHECK WITH rekordbox .39 6. SERVICE MODE.42 6.1 SERVICE MODE .42 6.2 ABOUT THE DEVICE.64 7. DISASSEMBLY .65 8. EACH SETTING AND ADJUSTMENT.83 8.1 NECESSARY ITEMS TO BE NOTED.83 8.2 UPDATING OF THE FIRMWARE.84 8.3 ITEMS FOR WHICH USER SETTINGS ARE AVAILABLE.86 9.

8、EXPLODED VIEWS AND PARTS LIST.88 9.1 PACKING SECTION.88 9.2 CHASSIS SECTION.90 9.3 DISPLAY SECTION.92 9.4 CONTROL PANEL SECTION (1/5).94 9.5 CONTROL PANEL SECTION (2/5).96 9.6 CONTROL PANEL SECTION (3/5).98 9.7 CONTROL PANEL SECTION (4/5).99 9.8 CONTROL PANEL SECTION (5/5).101 9.9 JOG DIAL SECTION .

9、102 RadioFans.CN 收音机爱 好者资料库 4DDJ-RZX 1234 A B C D E F 1234 1. SERVICE PRECAUTIONS 1.1 NOTES ON SOLDERING 1.2 NOTES ON PARTS REPLACEMENT For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit. Be sure to use lead-free solder and a soldering iron that

10、 can meet specifications for use with lead-free solders for repairs accompanied by reworking of soldering. Do NOT use a soldering iron whose tip temperature cannot be controlled. The part listed below is difficult to replace as a discrete component part. When the part listed in the table is defectiv

11、e, replace whole Assy. Assy Name Parts that is Diffcult to Replace Ref No.FunctionPart No.Remarks Assy Name Parts that is Diffcult to Replace Ref No.FunctionPart No.Remarks MAIN Assy JFLB1 Assy IC1701U-PRO ICAM3352BZCZ80-KBGA IC1051 DC-DC CONVERTERBD9328EFJ-TBBIC with heat-pad (back side)IC1103 IC13

12、01 IC1201 ICBD9851EFV-TBBIC with heat-pad (back side) IC1251 IC2601 AUD DSP SYS LSID810K013DZKB456-KBGA IC3101 IC3602PLL ICSI5351C-B03300GM-TBBQFN IC with heat-pad (back side) V6001 JFLB2 AssyV6101 IC1601PO SUPPLY ICTPS65910A31A1RSL-TLBQFN IC with heat-pad (back side) IC4901 INTERFACE ICUSB2512B-AEZ

13、G-TR-TBBIC with heat-pad (back side) RAM ICW631GG6KB-12-KBGA JOG FLDEL1074-A Repair the JOG FL and FL holder after removing them as integrated units. The part listed below is difficult to replace as a discrete component part. How to replace, refer to the remarks column. IC4951 IC1802RAM ICW631GG6KB-

14、12-KBGA LCDM Assy IC1381INTERFACE IC DRIVER IC AK4187VN-TLB BD81A04EFV-M-TBB IC with heat-pad (back side) IC1351 DC-DC CONVERTERBD9328EFJ-TBB IC with heat-pad (back side) IC with heat-pad (back side) U-PRO ICMCIMX6Q5EYM10AD-KBGA IC101 IC501 IC401PO SUPPLY ICMMPF0100F0AEP-KQFN IC with heat-pad (back

15、side) DC/DC CONV ICR1290K103A-TBBIC with heat-pad (back side) INTERFACE ICTFP401APZP-KIC with heat-pad (back side) IC1301 IC1201 IC601 IC602 LCDP Assy IC1881INTERFACE IC DRIVER IC AK4187VN-TLB BD81A04EFV-M-TBB IC with heat-pad (back side) IC1851 DC/DC CONV ICR1290K103A-TBB IC with heat-pad (back sid

16、e) IC with heat-pad (back side)IC1801 5DDJ-RZX 5678 5678 A B C D E F 1.3 SERVICE NOTICE The crossfaders and performance pads of this unit are calibrated on the production line. After you replace the corresponding part(s), be sure to perform calibration of the part(s) in question. See Crossfader cali

17、bration mode, PAD Calibration mode in 6.1 SERVICE MODE for details on how to calibrate. Without calibration, sound will not completely fade out even if a crossfader is set to its minimum-value position, or the volume changing in response to force applied to a performance pad will vary from one perfo

18、rmance pad to another in SAMPLER VELOCITY ON mode. For details on the specific parts for which recalibration is required, see 8.1 NECESSARY ITEMS TO BE NOTED. Calibration of the crossfaders and performance pads The same reference numbers are allotted to some electrical parts of the DDJ-SZ in this se

19、rvice manual. When searching for a part by its reference number in this manual, be sure to confirm the Assy name, as well as the reference number. Notes on 10. SCHEMATIC DIAGRAM and 12. PCB PARTS LIST Assy NameCircuit Block NamePart No.Ref No. MAIN Assy DIGITAL PWR AUDIO PWR VDET AM_PWR AM_EMIF DWX3

20、822 1001-1200 1201-1400 1401-1600 1601-1800 1801-2000 LCDM Assy IMX CLK/KEY/LED LCD3 HDMI RX DWX3828 1001-1100 LCD3 PWR/BL/TPNL 1201-1300 1301-1400 LCD3 I/F1401-1500 BOARD I/F1501-1600 LCDP Assy BOARD I/F LCD1/2 LVDS RX DWX3791 1601-1700 LCD1/2 PWR/BL/TPNL 1701-1800 1801-1900 LCD1/2 I/F1901-2000 The

21、 product which Firmware version is 1.03 or 1.04 is shipped holding the check results about touch panel of service mode. (Touch screen (test) of adjustment information mode is displayed OOO) It cannot be inspect in this state. (Check result of 4 squares is already all green) If you need to run touch

22、panel check, you should run factory reset before it. And select service mode, run touch panel check. The product which Firmware version is 1.05 or later is shipped after the check results have been cleared. About touch panel inspection 6DDJ-RZX 1234 A B C D E F 1234 SW POWER SUPPLY Primary side elec

23、trical shock The primary side of SW POWER SUPPLY Assy remains voltage long time, and the primary solder side can be seen. So if you touch the primary solder side, it is possible to receive an electrical shock. There is the red area below where we tend to receive an electrical shock. Be sure to disch

24、sarge the voltage of primary side to avoid receiving the electrical shock. When discharging the above point, use the following discharge jig as needed. While the charging voltage is left of both C4 and C5, either of checking LEDs turns on. And if both of LED turns off, we can avoid receiving the ele

25、ctrical shock! When there is no above type LED, take measures the following method. Step 1: After the power is turned off, wait 2 minutes. Step 2: Connect the Register Jig and leave the unit as it is, for 10 seconds. Resister is all 10 k (3W) Both of LED is LTL17KRH5D Checking LEDs No polarity C4C5

26、Electrical shock area of A-side. Electrical shock area of B-side. The circuit of discharge JIG is shown below. 7DDJ-RZX 5678 5678 A B C D E F 2. SPECIFICATIONS General Main Unit Power requirements . AC 110 V to 240 V, 50 Hz/60 Hz Power consumption. 48 W Power consumption (standby). 0.4 W Main unit w

27、eight.15.9 kg (35.1 lb) Max. dimensions.945 mm (W) 119.7 mm (H) 547 mm (D) (37.2 in. (W) 4.7 in. (H) 21.5 in. (D) Tolerable operating temperature.+5 C to +35 C (+41 F to +95 F) Tolerable operating humidity.5 % to 85 % (no condensation) Audio Section Sampling rate . 44.1 kHz/48 kHz/96 kHz MASTER D/A

28、converter. 32 bits Other A/D and D/A converters. 24 bits Frequency characteristic USB, CD/LINE, MIC1, MIC2. 20 Hz to 20 kHz S/N ratio (rated output, A-WEIGHTED) USB. 116 dB CD/LINE . 101 dB PHONO . 91 dB MIC1. 81 dB MIC2. 81 dB Total harmonic distortion (20 Hz 20 kHzBW) USB.0.002 % CD/LINE .0.003 % Standard input level / Input impedance CD/LINE .12 dBu/47 k PHONO .52 dBu/47 k MIC1.57 dBu/3 k MIC2.