Pioneer-DJMTour1-djm-sm电路图 维修手册.pdf

《Pioneer-DJMTour1-djm-sm电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Pioneer-DJMTour1-djm-sm电路图 维修手册.pdf（97页珍藏版）》请在收音机爱好者资料库上搜索。

1、ORDER NO. 6F, Yokohama i-Mark Place, 4-4-5 Minatomirai, Nishi-ku, Yokohama, Kanagawa 220-0012 JAPAN 2016 Pioneer DJ Corporation 2016 DJM-TOUR1 RRV4657 DJ MIXER DJM-TOUR1 THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S). THIS SERVICE MANUAL SHOULD BE USED TOGETHER WITH THE FOLLOWING MA

2、NUAL(S). ModelTypePower RequirementRemarks DJM-TOUR1LSYXJAC 110 V to 240 V DJM-TOUR1UXJCBAC 110 V to 240 V DJM-TOUR1XJCNAC 220 V ModelOrder No.Remarks DJM-TOUR1RRV4658SCHEMATIC DIAGRAM, PCB CONNECTION DIAGRAM, PCB PARTS LIST K-ZZZ AUG. RadioFans.CN 收音机爱 好者资料库 2DJM-TOUR1 1234 A B C D E F 1234 SAFETY

3、INFORMATION WARNING This product may contain a chemical known to the State of California to cause cancer, or birth defects or other reproductive harm. Health it is not meant for the casual do-it- yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to

4、properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely, you should not

5、risk trying to do so and refer the repair to a qualified service technician. RadioFans.CN 收音机爱 好者资料库 3DJM-TOUR1 5678 5678 A B C D E F CONTENTS SAFETY INFORMATION.2 1. SERVICE PRECAUTIONS.4 1.1 NOTES ON SOLDERING.4 1.2 NOTES ON REPLACING .4 1.3 SERVICE NOTICE.5 2. SPECIFICATIONS.6 3. BASIC ITEMS FOR

6、SERVICE .7 3.1 CHECK POINTS AFTER SERVICING .7 3.2 JIGS LIST.7 3.3 PCB LOCATIONS.8 4. BLOCK DIAGRAM .10 4.1 OVERALL WIRING DIAGRAM .10 4.2 AUDIO SYSTEM BLOCK DIAGRAM.11 4.3 DSP BLOCK DIAGRAM.12 4.4 POWER SUPPLY BLOCK DIAGRAM.13 5. DIAGNOSIS .14 5.1 POWER ON SEQUENCE.14 5.2 TROUBLESHOOTING.16 5.3 INF

7、ORMATION ON POWER DIAGNOSTICS .31 5.4 ERROR INDICATIONS.32 5.5 CONNECTION CHECK WITH EACH INTERFACE.33 6. SERVICE MODE.34 6.1 TEST MODE.34 6.2 ABOUT THE DEVICE.52 7. DISASSEMBLY .53 8. EACH SETTING AND ADJUSTMENT.75 8.1 NECESSARY ITEMS TO BE NOTED.75 8.2 UPDATING OF THE FIRMWARE.76 8.3 WRITING THE S

8、ERIAL NUMBER AND THE LANGUAGE SETTING OF THE UNIT.77 8.4 HOW TO MAKE PAIRING BETWEEN THE 13 INCH LCD MODULE AND THE MAIN ASSY.79 8.5 USER SETABLE ITEMS.82 8.6 HOW TO CHECK THE DVS .84 9. EXPLODED VIEWS AND PARTS LIST.86 9.1 PACKING SECTION.86 9.2 EXTERIOR and TITABLE DISPLAY SECIONS.88 9.3 CHASSIS S

9、ECION (1/2).90 9.4 CHASSIS SECION (2/2).92 9.5 CONTROL PANEL SECTION (1/2).94 9.6 CONTROL PANEL SECTION (2/2).96 RadioFans.CN 收音机爱 好者资料库 4DJM-TOUR1 1234 A B C D E F 1234 1. SERVICE PRECAUTIONS 1.1 NOTES ON SOLDERING 1.2 NOTES ON REPLACING For environmental protection, lead-free solder is used on the

10、 printed circuit boards mounted in this unit. Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs accompanied by reworking of soldering. Do NOT use a soldering iron whose tip temperature cannot be controlled. The part listed be

11、low is difficult to replace as a discrete component part. When the part listed in the table is defective, replace whole Assy. Assy Name Parts that is Diffcult to Replace Ref No.FunctionPart No.Remarks IC3002 MAIN Assy USBP Assy CDCB Assy CLK GeneratorSI5351C-B03300GMIC with heat-pad IC4507BD9328EFJI

12、C with heat-pad IC4512NJM78M15DL1AIC with heat-pad IC4852High Side SWTPS2557DRBIC with heat-pad HPPW AssyIC8001MM3543BHIC with heat-pad IC8002NJW4154GM1IC with heat-pad Q8210, Q8211, Q8213, Q8215 Transistor2SD1760F5 (R)Transistor with heat-pad Transistor with heat-pad Transistor with heat-pad Transi

13、stor with heat-pad Transistor with heat-pad Q8209, Q8212, Q8214, Q8216 Transistor2SB1184F5 (R)Transistor with heat-pad IC4902X-PAD TOUCH CONTROLLERATSAMD20E15A-MUIC with heat-pad IC with heat-pad IC with heat-pad IC with heat-pad IC with heat-pad IC4502NJM78M05DL1AIC with heat-pad IC2PMICTPS65910A31

14、A1RSLIC with heat-pad IC4503NJM78M05DL1AIC with heat-pad IC16LAN PHYLAN8720A-CPIC with heat-pad IC1MAIN UCOMAM3352BZCZ100BGA IC1501SRC_DSPD810K013DZKB456BGA IC9DDR3 SDRAMK4B1G1646G-BCK0BGA IC1001DSPD810K013DZKB456BGA ILMB AssyIC9801BD9328EFJ LANB Assy IC9001USB_LAN_IC for LINKRTL8152B-VB-CG IC9004US

15、B_LAN_IC for INTERNETRTL8152B-VB-CG IC9205HUB_SW_ICRTL8309M-CG HPP2 Assy Q8805Transistor2SD1760F5(R) Q8806Transistor2SB1184F5(R) Q8807Transistor2SD1760F5(R) Q8808Transistor2SB1184F5(R) 5DJM-TOUR1 5678 5678 A B C D E F 1.3 SERVICE NOTICE VOLTAGE MONITORING This unit always monitors for power failure

16、and will shut itself off immediately after an error is detected. A power failure is indicated with flashing of the QUANTIZE LED (Intervals: 250 ms Lit 125 ms/Unlit 125 ms). All the LEDs other than QUANTIZE LED will be unlit, and all the switches and VRs will be disabled. Repair the unit according to

17、 the diagnostic procedures described in 5.3 INFORMATION ON POWER DIAGNOSTICS. CROSS FADER Assy replacement Noncontact faders are adopted for the cross faders with this product. Compared with conventional contact-type cross faders, noncontact faders offer dozens of times the durability. Because high

18、accuracy is required for assembly of the fader section, the service part of this section will be supplied as a whole Assy. Use the CROSS FADER Assy (DXA2257) for replacement. After replacement, be sure to perform CFDR SET in Crossfader calibration mode of Test mode. If you dont, the unit may not sta

19、rt up properly. Note that performing CFDR SET in Cross Fader Calibration mode is also required after replacement of the MAIN Assy or PNLA Assy. CONFIRMATION OF USER-SETTING This product has user-setting data. Be sure to confirm those data before starting repair, although changing them may not have a

20、 large effect. Use the Check Sheet in 8.5 USER SETABLE ITEMS to which you can transcribe the settings, as required. The settings are stored in FLASH ROM (IC8) on the MAIN Assy. For details, refer to Changing the settings in the operating instructions. About replacing 13 inch LCD module Be sure that

21、the replacing service part is LCD FULL MODULE SERVICE ASSY (DEA1053). The MAC address written in the MAIN Assy should be stored in the 13 inch LCD module. FLASH ROM ON THE MAIN Assy Never replace the FLASH ROM (IC8) on the MAIN Assy during servicing. If the FLASH ROM is assumed to be defective, repl

22、ace the whole MAIN Assy. This FLASH ROM contains data that can only be written in at the factory. An IEEE 802.3-based MAC address specific to this unit has been written. About work after MAIN Assy replacement The writing of the unit serial No. is necessary when replacing the MAIN Assy. Refer to 8.3

23、WRITING THE SERIAL NUMBER AND THE LANGUAGE SETTING OF THE UNIT. Be sure to perform CFDR SET in Crossfader calibration mode in the test mode when replacing the MAIN Assy. It is unable to boot up normally if performing CFDR SET is neglected. Be sure to make pairing to the 13 inch LCD module when repla

24、cing the MAIN Assy. Refer to 8.4 HOW TO MAKE PAIRING BETWEEN THE 13 INCH LCD MODULE AND THE MAIN ASSY about the way of pairing. CDCB Assy replacement The touch defect of X-PAD is supposed to be composite reason as the defect of IC or assembling. Be sure that the replacing service part is X-PAD SERVI

25、CE ASSY (DEA1049). About USB-LAN Conversion IC in LANB Assy Do Not replace the USB-LAN Conversion IC (IC9001 and IC9004) in LANB Assy when servicing the Assy. When the USB-LAN Conversion IC is supposed to be defective, replace the LANB Assy. This USB-LAN Conversion IC saves the contents that is unab

26、le to write except at factory shipment. The unique IEEE802.3 MAC address of the unit is written. *The registration of the club information is required again by the new customer ID after servicing for the customer registered KUVO club informaion. Refer to Registering the club information in the web o

27、perating instructions about the way of registering club information. When perfopming replacing service of the LANB Assy, please inform to a customer returning a product that it is necessary to reregister the club information when installing the product. 6DJM-TOUR1 1234 A B C D E F 1234 2. SPECIFICAT

28、IONS General Power . AC 110 V to 240 V, 50 Hz/60 Hz Power consumption. 82 W Power consumption (standby). 0.4 W Main unit weight.16.1 kg (35.5 lb) External dimensions (When TILTABLE DISPLAY part is in closed state) .445.2 mm (W) 179.1 mm (H) 451.6 mm (D) (17.5 in. (W) 7.1 in. (H) 17.8 in. (D) (When T

29、ILTABLE DISPLAY part is upright at 90 degrees) .445.2 mm (W) 418 mm (H) 457.7 mm (D) (17.5 in. (W) 16.5 in. (H) 18 in. (D) (When TILTABLE DISPLAY part is in open state) .445.2 mm (W) 203.1 mm (H) 694.5 mm (D) (17.5 in. (W) 8 in. (H) 27.3 in. (D) Tolerable operating temperature.+5 C to +35 C (+41 F to +95 F) Tolerable operating humidity.5 % to 85 % (no condensation) Audio Section Sampling rate .96 kHz D/A converter. 32 bits A/D converter. 24 bits Frequency characteristic LINE. 20 Hz to 40 kHz S/N ratio (rated output) PHONO . 88 dB LINE. 1