Philips-DVP-3366-X-Service-Manual(1) 电路图 维修手册.pdf

《Philips-DVP-3366-X-Service-Manual(1) 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Philips-DVP-3366-X-Service-Manual(1) 电路图 维修手册.pdf（44页珍藏版）》请在收音机爱好者资料库上搜索。

1、TABLE OF CONTENTS Page Version 1.0 Service Manual . Technical Specifications.1-2 . Safety Instruction, Warning 525 (NTSC/60Hz) Playback: Multi-standard (PAL/NTSC) Video performance Video DAC: 12 bits, 108 MHz Y Pb Pr: 0.7 Vpp 75 ohm Video output: 1 Vpp 75 ohm Video format Digital compression: MPEG 2

2、: DVD/SVCD MPEG 1: VCD/DivX Horizontal resolution: DVD: 720/1920 pixels (50 Hz); 720/1920 pixels (60 Hz) VCD: 352 pixels (50 Hz); 352 pixels (60 Hz) Vertical resolution: DVD: 576/1080 lines (50 Hz); 480/1080 lines (60 Hz) VCD: 288 lines (50 Hz); 240 lines (60 Hz) Audio performance DA converter: 24 b

3、its, 192 kHz Frequency response: DVD: 4 Hz - 22 kHz (48 kHz); 4 Hz - 44 kHz (96 kHz) SVCD: 4 Hz - 20 kHz (44.1 kHz); 4 Hz - 22 kHz (48 kHz) CD/VCD: 4 Hz - 20 kHz (44.1 kHz) Signal-Noise (1 kHz): 90 dB (A-weighted) Dynamic range (1 kHz): 85 dB (A-weighted) Crosstalk (1 kHz): 85 dB Distortion/noise (1

4、 kHz): 70 dB MPEG MP3: MPEG Audio L3 Audio format Digital: MPEG/AC-3/PCM: Compressed digital (16, 20, 24 bits fs, 44.1, 48, 96 kHz) MP3 (ISO 9660): 96, 112, 128, 256 kbps IEC61937 for MPEG 1/2, Dolby Digital HDMI output 5.1 channel analog output Audio Front L+R: Cinch (white/red) Audio Rear L+R: Cin

5、ch (white/red) Audio Center: Cinch (blue) Audio Subwoofer: Cinch (black) 1-2 RadioFans.CN 收音机爱 好者资料库 Safety instruction 1. General safety Safety regulations require that during a repair: . Connect the unit to the mains via an isolation transformer. . Replace safety components indicated by the symbol

6、 , only by components identical to the original ones. Any other component substitution (other than original type) may increase risk of fire or electrical shock hazard. Safety regulations require that after a repair, you must return the unit in its original condition. Pay, in particular, attention to

7、 the following points: . Route the wires/cables correctly, and fix them with the mounted cable clamps. . Check the insulation of the mains lead for external damage. . Check the electrical DC resistance between the mains plug and the secondary side: 1) Unplug the mains cord, and connect a wire betwee

8、n the two pins of the mains plug. 2) Set the mains switch the “on” position (keep the mains cord unplug). 3) Measure the resistance value between the mains plug and the front panel, controls, and chassis bottom. 4) Repair or correct unit when the resistance measurement is less than 1M?. 5) Verify th

9、is, before you return the unit to the customer/user (ref. UL-standard no. 1492). 6) Switch the unit “off”, and remove the wire between the two pins of the mains plug. 2.Laser safety This unit employs a laser. Only qualified service personnel may remove the cover, or attempt to service this device (d

10、ue to possible eye injury). Laser device unit Type : Semiconductor laser GaAlAs Wavelength : 650nm (DVD) : 780nm (VCD/CD) Output power : 7mW (DVD) : 10mW (DVD /CD) Beam divergence: 60 degree Note: Use of controls or adjustments or performance of procedure other than those specified herein, may resul

11、t in hazardous radiation exposure. Avoid direct exposure to beam. Safety instruction, Warning 2) Press the Setup button on the remote control,then the setup interface should be displayed on the TV screen; 3) Move the down cursor on remote control to choose Reference and press 1 3 8 9 3 1 on the remo

12、te control; 4) Then move the up or down cursors to choose the region code. Note: restart after above steps. * The other upgrade SW way is by memory, the steps are the same as CDRs, create the upgrade file into memory, and connect the USB flash drive to the USB socket on set, then press USB on remote

13、 control to access the content and play the upgrade file as above upgrade procedure. * 2) Press button or press down cursor on remote control to choose Preference and press right & down cursors to choose Version Info. Model DVP33XXX XX File Name DVP33XXX XX.BIN Version XX.XX.XX.XX RISC XX.XX.XX.XX S

14、ervo XX.XX.XX.XX Region Code X HDCP PASS(except press) 5-1 Spindle motor does not move Yes Yes No No No No Yes Check whether “M5V” (+5V) voltage is normal. Correct connection Check the M5V power supply Check/Replace Q5,Q6,Q7,Q8. Check/ Replace U1. Check opu focus 1. Check U1 25pin FOCUS_PWM signals

15、2.If there are F+, F-, T+ and T- signals output from U2. Check/Replace the loader Yes Yes No Go Check whether laser voltage (1.9V for CD & 2.4V for DVD) on L9 and L10 Check the FFC connection between 24P and the loader. 1.Whether voltage on pin 23 of U1 varies between 0 and 3.3V (3.3V for CD and 0V

16、for DVD), 2.Whether peripheral components are eroded or badly soldered. Trouble shooting chart Motor no move FOCUS_PWN waveform 5-2 The power can not be on or off Go Yes Yes No No The power cant be on or off Yes Repair the power board Check the power supply on the power board is normal. Check/Correc

17、t connection Whether the connection to K301 is broken. Correct the connection Replace U1. No No Yes Yes Check if the XS301 on the front board to XP5 on the decoder board is in good contact. Whether there is 0V and 3.3V voltage difference on Pin 106 PCON of U1. Trouble shooting chart 5-3 All output v

18、oltages on the power board is 0V or deviated. No No No Yes No U1(PIN 8 - Drain waveform) Replace F1 Replace C1&C2 if D1, D2, D3, D4 are normal. Check/ replace U1. Check whether U1 are eroded. All output voltages on the power board is 0V or deviated Check whether there is 300V on C1 or C2. Check whet

19、her 100KHz oscillating signal on Pin6 of U1 Check if +5V and +12V are short. Check whether the components in the short-circuit voltage are defected or eroded. Yes Yes Yes Yes U1(PIN 3 - RC waveform) Trouble shooting chart Check whether F1 is blown 5-4 Disc cannot be read. No Yes No Yes No Yes Yes No

20、 No Yes Disc cannot be read. Check the loaded circuit 1.Check voltage on pin 23 of U1 varies between 0 and 3.3V: ?3.3V for CD ?0V for DVD 2.Check whether peripheral components are eroded or defect Check the FFC connection between 24P and the loader. Check U1 and peripheral components Re-solder or re

21、place the defective parts Check the connection between U1 Correct connection Replace U1 or loader. Yes Check whether there is laser voltage (1.9V for CD and 2.4V for DVD) on L9 and L10. Check if there is RFO signal on pin17 of XP2. (The normal RFO signal is a clear reticulated wave) Trouble shooting

22、 chart Check U1, U2, and peripheral components are eroded or badly soldered. 5-5 Only DVD disc or only disc except DVD can be played No No Yes Only DVD disc, or only disc except DVD can be Played. Check the FFC connection between 24pin and the loader. Check the loaded circuit Check the solder status

23、 on U1 and peripheral components Check whether there is voltage variance on pin 25 of U1. check if bad solder exist on U1 and peripheral components Replace the bad spare parts Check whether pins of U1 and peripheral components are badly soldered, defected Check Q5, Q7 whether in good condition Yes Y

24、es Yes Go Correct connection Change U1 or the loader. No No Yes Check laser voltage (2.4V) output on L10, if pin18 of U1 is at low level. Trouble shooting chart No 5-6 No display on LED, and buttons do not work No No No Yes Yes No display on LED, and buttons do not work Check whether there is correc

25、t contact between XS301 and XP5 Correct connection Fix power supply board top a power supply for should electric circuit Check the U1s pin 87,41,40 arrive the XP5 connect condition Correct connection Replace U301 or LED Yes Yes Yes No Check VCC(+5v) voltage on the power and front board Check there a

26、re STB, SDA and SCK signals on XS301 on the front board. 1.Check whether bad solder exists on U301 and pins of LED, 2.Check whether the circuit connected to K302, K303, K304 and K301 is broken, 3.Check whether R300, R301 and R302 are open-circuit. Trouble shooting chart XP5 (PIN 1 CLK) XP5 (PIN3 DOU

27、T) 5-7 Distorted audio and loud noise No Yes No Yes Yes No No Distorted audio and loud noise Replace R84, R94,R100,R107,R116,R124 Check Q3 Replace Q11Q19 Check whether the muting transistor R84,R94,R100,R107,R116,R124 are normal Yes Check whether the muting transistor Q11,Q12, Q13,Q15,Q17,Q19are nor

28、mal Checking the U6 leads the feet has no to break to open ? Replace R86,R87 Check the voltage on pin3 or pin5 of U6 is OK. (Should be 2.53.1V) Check whether the U1 or U6 powersupply normal No Yes Check the power supply voltages +12V to the operation amplifying Q3 is normal. Yes Check U6 Replace U1

29、or U15 No Yes Trouble shooting chart 5-8 Abnormal color of video picture Yes Abnormal color of video picture Check whether the 3.3V and 1.8V power supply voltages on the decoder board are normal. Check Y2, R20,R27,C22 and C23 Check other of power supply electric circuit Correct the connection Check

30、whether the video filter network circuit is normal. Yes Yes No No No Check whether the 27MHz output signal Trouble shooting chart change U1 Yes No Check if the video signals on Pin 99,102,103,104, of U1 are normal 5-9 Remote reception is insensitive or fails. No Remote reception is insensitive or fa

31、ils. Check if the remote control works properly. Check battery Check R315?C315 Use an oscilloscope to check if there is output waveform from the first pin IR of the remote censor after pressing button on the remote control. REM301(PIN1 - RC waveform) Check if there is IR signal on pin 44 of U1 Check

32、 if the power supply voltage to the remote censor is normal Go No No No Yes Yes Yes Correct connection Yes Change U1 IR waveform Trouble shooting chart 5-10 No video picture, no sound. Change CE7, D2. No video picture, no sound. Check if the reset circuit consisting ofCE7, D2 is normal (at a low lev

33、el for tens of milliseconds, then constantly at 3.3V). Check whether there is 27MHz signal output. Check the loaded circuit Crystal oscillator Y2 and peripheral components are defected or eroded. No No No Yes Yes Yes 27Mhz waveform Trouble shooting chart Check whether all the voltages from the power

34、 board to the decoder board are normal. CVBS(R21 point) waveform Check if there is 128MHz signal output on R67. Check whether short-circuit or bad solder on U4,U5 SDRAM(R67 DCLK) waveform Check U1. No No Reconnect the component in Yes Yes Check if short-circuit and bad solder exist on Pin 99 Yes No

35、A A B B C C D D E E 11 22 33 44 12V GND 5V GND SP+ LOAD- TRIN GND LOAD+ TROUT GND LIMIT SP- 5V SL- SL+ GND 5V IR LED+ PCON/LED_ VSTB GND POWER_K 5V 12V VSDA VSCK GND USB_DP GND USB_DM MIC TCL LOADER+IM S76RFXP FLASH 6 11PIN*2.0 POWER SUPPLY 24 1 5 1 1 5 1 1 6 DVD LOADER 5PIN*2.0 6PIN*2.0 5PIN*2.5 24

36、PIN*0.5 5PIN*2.5 XP1 XS201 XP5 XP3XP4XP2 1 5 MT1389DXE/M AM5888 AUDIO AMP&LPF MOTER DRIVER VIDEO LPF 64M SDRAM DVP3366K 6CH WIRING DIAGRAM 61 XS301 11PIN*2.0 LED DISPLAY+ET6202 4 1 XS302 4PIN*2.0 17 KARAOKE AND USB XS601 8PIN*2.0 XP303 SWITCH BOARD4PIN*2.0 4 1 XP74PIN*2.0 14 COAX P2 R L XP6 MAIN BOA

37、RD 13 HDMIP3P1 Pb Y Pr CVBS REAR L REAR R CENTER SUB P4 16M Serial 6-1 6-1 5 5 4 4 3 3 2 2 1 1 DD CC BB AA CLK 5VL IR CS DATA CLK CS KEY2 DATA SEG1:6 VCC WAKE_SW POWER_K1 LED+ LED-STB_LED KEY1 POWER_K1 LED- U5VLED+ GRID6 GRID5 SEG6 SEG1 SEG5 SEG15VL SEG2 SEG4 SEG5 GRID6 GRID3 GRID1 GRID4 SEG4 SEG3 G

38、RID2 SEG6 GRID1:7 GRID3 GRID4 GRID1 GRID2 GRID7 GRID5 GRID7SEG2 SEG3 WAKE_SW U5V KS2POWER_K STB_LED IR POWER_K POWER_K VCC VCC U5V ? IR VCC GND DATA CS CLK for dvp331x C300 100P XS302 CON4(2.0) 1 2 3 4 C301 100P R315 100 ohm C302 100P U301 ET6202 OSC 1 DI/O 2 CLK 3 STB 4 KEY1 5 KEY2 6 VDD 7 SEG1/KS1

39、 8 SEG2/KS2 9 SEG3/KS3 10 SEG4/KS4 11 SEG5/KS5 12 SEG6/KS6 13 SEG7/KS7 14 GND 28 GRID1 27 GRID2 26 GND 25 GRID3 24 GRID4 23 GND 22 VDD 21 SEG14/GRID5 20 SEG13/GRID6 19 SEG12/GRID7 18 SEG10/KS10 17 SEG9/KS9 16 SEG8/KS8 15 + CE300 47uF C310 0.1uF R3200R C315 47p C309 0.1uF + CE301 47uF R318 100R/NC R3

40、0710K R30810K R303 4K7 R304 4K7 R3091K R305 4K7 K301 open/close REM301 REM IR 1 GND 2 VCC 3 4 4 5 5 C304 100p C305 100p C316 100p R3101K R3111K R3121K R300100 C306 0.1u K302 play/pause R306 51K R31733R R301100 D3021N4148 LED1 JDD350501AG GRID1 1 GRID2 2 GRID3 3 GRID4 4 GRID5 5 GRID6 6 GRID7 7 SEG1 8

41、 SEG2 9 SEG3 10 SEG4 11 SEG5 12 SEG6 13 R3140R/nc R302100 D3011N4148 XS301 CON11(2.0) 1 2 3 4 5 6 7 8 9 10 11 R3131K C307 100p C303 0.1u C308 100p R3190R R31633R Front Board Electric Diagram 7-17-1 A A B B C C D D E E 11 22 33 44 SWITCH BOARD C319 47p C317 47p C318 47p XP1 CON4(2.0) 1 2 3 4 LED3 K30

42、3 POWER Switch Board Electric Diagram 7-27-2 1 1 2 2 3 3 4 4 5 5 AA BB CC DD EE REF 12VA MIC_OUT USB_DP USB_DN 12VA 12V MICMIC_OUT REF SGND MGND MGND USB_DP VCC USB_DN 12V12VA SGND AGNDMGND MGNDAGND MGNDSGND VCC ?3.5mm 47-EAR024-XX0 KARAOKE P601 KARAOKE INPUT 1 2 3 C208 100p R202 22K L201 500Z 47-US

43、B003-XX2 USB P600 USB 1 2 3 4 5 6 C203 1000p R206 20K R209 680 CE200 22uF C210 2.2uF + - U200A NJM4558 3 2 1 84 + - U200B NJM4558 5 6 7 84 C20647p R205180K R211 100K X2TITLE-PART R210 150 R203 22K R208 1K R200 10K L202 500Z C201 0.1u L200 500Z C20547p CE201 22uF C211 2.2uF R201 5.6K R207100K 8PIN/2.

44、0mm XP601 1 2 3 4 5 6 7 C204 100p C209 2.2uF OK Board & USB Board Electric Diagram 7-37-3 A A B B C C D D E E 11 22 33 44 PLEASE USE THE PARTS HAVING THE DESIGNATED PARTS NUMBER WITHOUT FAIL. * CAUTION : THE PARTS MARKED WITH ARE IMPORTANT PARTS ON THE SAFETY. AC INPUT C11 0.1uF/63V CY1 102/400Vac +

45、C6 47uF/25V + C8 470uF/16V D8 IN4007 L6 ? ? D10SR360/SR340 U1 TNY176/177 S 8 EN/UV 1 S 5 S 6 Drain 4 S 7 NC 3 BP/M 2 R11 1/6W22 CN1 AC INPUT + 1 + 2 +C2 15uF/400V(250V/450V) D1 1N4007 D5 FR102 R7 1/6W11.3k 1% R13 1/6W100k T1EEL19 8 6 3 5 9 12 10 4 7 11 1 D3 1N4007 P3 1 C5 152/1KV R9 1/6W10k CON1 AC INPUT + 1 + 2 L2 6.8uH U3 TL431 2 1 3 D2 1N4007 F1 T2AL/250ac +C1 10uF/400V(250V/450V) TR1 NTC 10&20 R1 NU R5 1/6W12K 1% CON2 6X2.5 HEADER +5V 1 +5V 2 GND 3 +12V 4 GND 5 -22V