Philips-BDP-9000-Service-Manual(1) 电路图 维修手册.pdf
《Philips-BDP-9000-Service-Manual(1) 电路图 维修手册.pdf》由会员分享,可在线阅读,更多相关《Philips-BDP-9000-Service-Manual(1) 电路图 维修手册.pdf(105页珍藏版)》请在收音机爱好者资料库上搜索。
1、Blu-ray Disc Player Model BDP9000 Service Manual Contents Pag e 1. About this Manual 2 Contents Page 2. Safety Instructions, Warnings and Notes 3 3. System Overview 5 4. Technical Reference 7 5. Required Equipment List 13 6. Diagnosis and Repair Flowchart 14 7. Software Update and Repair 27 8. Mecha
2、nical Instructions 28 9. Circuit Diagrams and PWB Layouts 35 10. Spare Parts List 70 11. Directions for Use 73 Copyright 2006 Philips Consumer Electronics B.V. Eindhoven, The Netherlands. All rights reserved. No part of this publica ion may be reproduced, stored in a retrieval system or transmitted,
3、 in any form or by any means, electronic, mechanical, photocopying, or o herwise without prior permission of Philips. Published by Consumer Electronics Printed in the Netherlands Subject to modification EN 0000 000 00000 RadioFans.CN 收音机爱 好者资料库 EN 2 1. BDP9000 About this Manual 1. About this Manual
4、1.1. Content of this Manual Note: The BDP9000 will be serviced on a modular level only. Faulty modules will be identified and replaced. Detailed circuit diagrams and technical information on a component level are therefore not provided in this document. 1.1.1. What is included in this Manual Safety
5、Information System Overview Basic System Block Diagrams Parts / Module Identification Module Functional Descriptions Basic Module Technical Descriptions Basic Measuring Point Information Basic Fault Finding Strategy Module Removal DVD: All or 1) For DVD+R discs, make sure that the disc is finalized.
6、 Clean the disc. Cannot play JPEG files from a disc.Make sure that the disc was recorded in the UDF, ISO9660 or JOLIET format. Cannot play MP3 files from a disc or a memory card. Make sure that the disc was recorded in the UDF, ISO9660 or JOLIET format. Make sure that the bit rate of the MP3 files i
7、s between 56 and 320 kbps. Make sure that the sample rate of the MP3 files is 32 kHz, 44.1 kHz or 48 kHz. Cannot play a memory card.Make sure the memory card is supported by the product. Red cross in the upper right hand corner of the screen. The operation is not possible. Cannot find a JPEG file.Ma
8、ke sure that the selected folder does not contain more than 1500 files. Only the first 1500 files are shown. Make sure that the file extension is .jpg, .JPG, .jpeg or .JPEG. Cannot find an MP3 file.Make sure that the selected folder does not contain more than 1500 files. Only the first 1500 files ar
9、e shown. Make sure that the file extension is .mp3 or .MP3 The product gives no response to any control. Press and hold the standby/on button for 5 seconds to set the product to stand-by. ProblemTip EN 36 Technical data Dimensions Operating environment Power Video output Audio output When you play a
10、 video from a disc, the audio is dependent upon: The type of audio connection The disc type and the audio on the disc The selected digital audio format (only for S/PDIF and HDMI connections) Product dimensions (W x D x H)16.9 x 12.8 x 3.1 in (430 x 325 x 789 mm) Product weight9.3 lbs (4.2 kg) Operat
11、ing temperature41 to 104 F (+5 to 40 C) Operating humidity10 to 75 % (non-condensing) Mains powerAC, 120 V, 60 Hz Standby/on switch Power consumption51 W (The TV mode light comes on. 3Make sure that you can operate the TV with the universal remote control. Refer to Overview on page 5 for an overview
12、 of the functions of the keys and the buttons. Identify devices Manually If a device does not react correctly to the universal remote control, you must identify the device yourself. The instructions are applicable to a TV. You can use the same pro- cedure to identify other devices (for example, DVD
13、players or home theather systems). 1Turn the TV with its own remote control or the TV. 2Go to the first TV channel. If the device does not react correctly to the universal remote control, you must identify the device yourself (refer to Identify devices). EN 8 3Press the mode selector until the TV li
14、ght comes on. 4Find the first code for the TV in the TV code list (refer to Codes on page 16). 5Press-and-hold the 1 and 3. 6When the TV light flashes two times, release the 1 and 3. 7Enter the code from step 4. 8Make sure that you can operate the TV with the universal remote control. Refer to Overv
15、iew on page 5 for an overview of the functions of the keys and the buttons. Search automatically for the correct code 1Turn the TV on with its own remote control or the controls on the TV. 2Go to the first TV channel. 3Press the mode selector until the TV light comes on. After the first and second d
16、igits, the TV light flashes one time. After the third digit, the TV light goes off and flashes two times. If the device does not react correctly to the universal remote control: 1Find the next code in the code list. 2Go back to step 5. OR: 1Search automatically for the correct code. EN 9 4Press-and-
17、hold the 1 and 3. 5When the TV light flashes two times, release the 1 and 3. 6Press the stand-by button. The universal remote control searches automatically for the signal that turns the TV off. Each time that the universal remote control transmits a signal, the TV light in the display flashes. 7Whe
18、n the TV is turned off, press the stand-by key. 8Make sure that you can operate the TV with the universal remote control. Refer to Overview on page 5 for an overview of the functions of the keys and the buttons. Enjoy Volume buttons Depending on the selected mode, the volume buttons are assigned to
19、the TV or the amplifier: These are the factory settings: You can change the assignment of the volume controls. For example, you can assign the volume button in the TV mode to the amplifier: 1Select the TV mode. ModeVolume buttons BDTV TVTV AMPAmplifier SATTV DVDTV EN 10 2Press-and-hold the 1 and 6 u
20、ntil the TV mode light flashes two times. 3Press the 9. The mode light flashes one time. 4Press the 9 again. The mode light flashes one time. 5Press the 3. The mode light flashes two times. EN 11 6Select the AMP mode. 7Press any button. The volume button is assigned to the amplifier. Copy functions
21、You can copy the function of a device from its own mode to another mode. For example, the mute button of the AMP mode to the TV mode. Then, you can mute the amplifier in the TV mode. 1Select the AMP mode. 2Press-and-hold the 1 and 6 until the AMP mode light flashes two times. EN 12 3Press the 9. The
22、 mode light flashes one time. 4Press the 9 again. The mode light flashes one time. 5Press the 5. The mode light flashes one time. 6Press the mute button (the source button). The mode light flashes one time. 7Select the TV mode. The TV mode light comes on. 8Press the target button. The function is co
23、pied. EN 13 Restore the factory default settings 1Press-and-hold the 1 and 6 until the mode light flashes two times. 2Press the 9. The mode light flashes one time. 3Press the 8. The mode light flashes one time. EN 14 4Press the 1. The mode light flashes two times and the factory default settings are
24、 restored. Replace the batteries 1Open the battery compartment. 2Remove the used batteries. 3Insert the new batteries correctly. 4Close the battery compartment. WARNING DO NOT USE OLD AND NEW BATTERIES OR DIFFERENT TYPES OF BATTERIES IN COMBINATION. IF YOU DO, THE BATTERIES CAN LEAK CHEMICALS. THE C
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Philips-BDP-9000-Service-Manual1 电路图 维修手册 Philips BDP 9000 Service Manual 维修 手册
收音机爱好者资料库所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。



Marshall-9100-62-02-Schematic电路原理图.pdf


