shure_uc4_sm 电路图.pdf

《shure_uc4_sm 电路图.pdf》由会员分享，可在线阅读，更多相关《shure_uc4_sm 电路图.pdf（33页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL CHANGE NOTICE UC4 DIVERSITY RECEIVER Changes or corrections have been made to this service manual. Update your service manual by replacing the pages listed in the table below with the ones attached to this change notice. CHANGES EFFECTIVE DATE REMOVE these pages from your current manu

2、al INSERT the following revised pages attached to this notice Revision 1 pages: ALLRevision 2 pages: ALL Revision 2 pages: 14,15,19,20,21,22,26,27 and 30Revision 3 pages:14,15,19,20,21,22,26,27 and 30 SERVICE MANUAL REVISION HISTORY ReleasePart NumberDate Code Original25A1045RI Revision 125B1045SB R

3、evision 225C1045TB Revision 325C1045TK Shure Incorporated 222 Hartrey Avenue Evanston IL 60202-3696 U.S.A. UC UHF Wireless System ?1999, Shure Incorporated Printed in U.S.A. RadioFans.CN 收音机爱 好者资料库 ?1999, Shure IncorporatedPrinted in U.S.A. 25C1045 (TK) Service Manual UC4 Diversity UHF Receiver 25C1

4、045 (TK) Characteristics General The Shure UC4 Diversity UHF Receiver is a microprocessor- controlled single diversity receiver operating in the 692 to 716 MHz and 774 to 862 MHz frequency range. The UC4 is used in mid-level installed sound, rental, and concert sound applications. Controls and Conne

5、ctors 1.Diversity Indicators 2.Squelch Control 3.Rf Level Indicators 4.Audio Level Indicators 5.Low Transmitter Battery Indicator 6.Group Rotary Switch 7.LED Display 8.Channel Rotary Switch 9.Equalization (EQ) Adjustment Controls 10. Level (Volume) Control 11. Power On/Off Switch 12. Power Input Con

6、nector 13. Balanced (LOW Z) Output Connector 14.MIC/LINE Side Switch 15. Unbalanced (HIGH Z) Output Connector 16.LOGIC OUT Connector 17. Antenna Input Connectors Figure 1.UC4 Controls and Connectors AB R 1 58 10 346 12 119 1314151617 7 2 Service Note: Shure recommends that all service procedures be

7、performed by a Factory- Authorized Service Center or that the product be returned directly to Shure Incorporated. Licensing: Operation may require a user license. Frequency or power-output modifica- tions may violate this products approvals. Contact your countrys communications authori- ties. RadioF

8、ans.CN 收音机爱 好者资料库 Shure UC4 Diversity Receiver 2Parts Designations25C1045 (TK) Circuit Description The audio circuit and rf circuit description will describe only one channel because the other channel is identical for both. The local oscillator (LO) section is common for both channels and will be de

9、scribed separately. Audio Section Figure 2.UC4 Audio Section Block Diagram AUDIO A AUDIO B 4-POLE LP FILTER COMPANDERDE-EMPHASIS TONE CONTROL OUTPUT STAGE XLR OUT 1/4” OUT TO AUDIO LEVEL BAR DISPLAY SQUELCH NOISE A NOISE B MARCAD DIVERSITY CIRCUIT TONE KEY DETECTOR MUTING CIRCUIT LOW BATTERY DETECTO

10、R TTL CIRCUIT TTL OUT The audio for each channel comes from the appropriate channel detector output of the rf section. Each channels audio then enters its own adjustable gain stage. This adjustable gain stage is used to match the audio levels coming from each rf channel, as well as to set the correc

11、t level necessary for the compander. From the gain stages, each channel enters an analog switch. Noise outputs also come from each channel detector outputs. Each noise output enters a bandpass noise filter that measures the 50 kHz noise present in the audio signal. The noise level is proportional to

12、 the signal- to-noise ratio of the channel. In the MARCAD diversity system, a rectified version of the noise is sent to a bank of comparators. A version of the channel noise that is 6 dB less also enters the comparators. The noise from one channel is compared to the noise from the other to make sure

13、 they are within 6 dB of each other. If the noise levels are within 6 dB of each other, the comparators send a logic high signal to the control of each channels analog switch, allowing the audio to pass through. RadioFans.CN 收音机爱 好者资料库 Shure UC4 Diversity Receiver Parts Designations325C1045 (TK) If

14、the noise levels are not within 6 dB of each other, the channel with a noise voltage 6 dB greater than the other channel is not allowed to pass through the analog switch; that is, the comparator puts a logic low signal on the control line for the analog switch. Each channels noise is also compared t

15、o an adjustable squelch level; a dc level. If either noise voltage is greater than the squelch threshold, it is shut off. The outputs from the analog switches are connected together at the audio combining stage, a unity gain buffer stage where the audio from Channel A is combined with the audio from

16、 Channel B. The output from this stage splits into three paths. The first path goes to a high Q tone key detection circuit. This is a crystal filter in which the level of tone key is converted to dc and compared against a fixed dc volt- age. The second path enters a low Q bandpass filter centered ar

17、ound 32 kHz. This filter is for low battery detection in the receiver. The lower Q allows for small frequency variation of tone key from various transmitters, without the large amplitude variations that the crystal filter would have. The filtered signal is then rectified and averaged. The dc that is

18、 obtained from this is amplified, triggering a comparator for the low battery LED display. The third path is into the compander via a 24 kHz low-pass filter with a 32 kHz notch. The audio is expanded and de-emphasized here. The compander output then goes off the board to a high and low frequency equ

19、alization circuit. A user-adjustable gain stage follows. The signal is then brought back to the main audio board, where it enters a balanced and unbal- anced output stage. The balanced output can be set for either mic or line level, where the mic level is 30 dB down from the line level. For the audi

20、o level meter, audio is tapped off from the 24 kHz filters output and goes through a full wave precision rectifier and averaging cir- cuit. This dc signal then enters a dc amplifier stage used to adjust levels for the LEDs. The output from this stage drives the audio level meter on the front panel b

21、oard. For the rf level meters, a dc voltage from the detector chip for the received signal strength indicator (RSSI) drives the bargraph IC on the front board. Shure UC4 Diversity Receiver 4Parts Designations25C1045 (TK) Rf Section Figure 3.UC4 Rf Section Block Diagram DIELECTRIC FILTER DIELECTRIC F

22、ILTER LNA FIRST MIXER SECOND MIXER FIRST IF FILTER SECOND IF FILTER FM DETECTOR AUDIO A NOISE A RSSI A RF CHANNEL A DIELECTRIC FILTER DIELECTRIC FILTER LNA FIRST MIXER SECOND MIXER FIRST IF FILTER SECOND IF FILTER FM DETECTOR AUDIO B NOISE B RSSI B RF CHANNEL B FROM MICROPROCESSORSYNTHESIZERVCO LOW

23、PASS FILTER FIRST LO SECOND LO The rf input signal is provided from the antenna ports to the receiver by BNC connectors. Antenna port A is connected to J101 (channel A), and antenna port B is connected to J201 (channel B). The rf circuit description will describe only one channel because the other r

24、f channel is identical. The local oscillator (LO) section is common for both channels and will be described separately. Rf Channel The rf signal is pre-selected to the 782 806 MHz frequency range with two dielectric filters. The first dielectric filter is located between the antenna port and the low

25、 noise amplifier (LNA). The second filter is located between the LNA block and mixer input. The LNA and the first mixer consist of a dual gate GaAs MOSFET. The first conversion gives the first intermediate frequency (IF) signal at 50 MHz. The first IF signal is amplified with MMIC, band limited with

26、 a SAW filter, and then down-converted to the second intermediate frequency (IF) at 10.7 MHz with a second down-converter. The second IF signal is filtered by 10.7 MHz ceramic filters and amplified by a 10.7 MHz pre-amp (Q105). The 10.7 MHz signal goes to the second IF gain block with a detector. Th

27、e audio output is buffered and then processed as stated in the audio section circuit description. The noise output is amplified to pro- vide signal for the noise squelch circuitry. The Received Signal Strength Indication (RSSI) output of the detector drives the LEDs that are located on the receivers

28、 front panel. Shure UC4 Diversity Receiver Parts Designations525C1045 (TK) Local Oscillator (LO) The first local oscillator (LO) is common for channel A and channel B rf strips. The LO is a phase-locked loop (PLL) system. The PLL consists of a prescaler/synthesizer, voltage-controlled oscillator (VC

29、O), a loop filter, a VCO, an rf power divider, and a bandpass filter. The PLL limits the LO signal before injection to the first down con- verter, Q102 and Q202. The prescaler receives the rf signal from the VCO via the coupling capacitor, C333. The output from the phase detector is connected to an

30、external loop filter that controls the tuning voltage input to the VCO. The prescaler/synthesizer IC is a serial-programmable input IC. It receives the frequency programming data from the microprocessor, which is set by the user, as described in the digital circuit description. Digital and Display S

31、ection EEPROM MICROPROCESSOR ROTARY SWITCH (CH) ROTARY SWITCH (FREQ) SHIFT REGISTER SHIFT REGISTER LED DRIVER LED DRIVER LED DRIVER5 LED BAR 7 LED BAR 5 LED BAR TO SYNTHESIZER AUDIO RSSI A RSSI B Figure 4.UC4 Digital and Display Section Block Diagram Shure UC4 Diversity Receiver 6Parts Designations2

32、5C1045 (TK) Microcontroller The microcontroller section consists of a U703 microcontroller and a two digit, seven segment, LED display. The LED display indicates frequency in terms of compatible channels in a group. The LED display on the left indicates the current group. The LED display on the righ

33、t indicates the channel. Each LED is capable of displaying digits 0 9. However, the channel LED also displays alpha letters A F. Serial shift registers, U705 and U705, latch the current LED display. A serial Load Enable (LE) signal of the display driver section is also shared with the rf interface s

34、ection. A 4.0 MHz oscillator, Y701, provides the operating frequency to the microcontroller. The oscillator circuit includes capacitors C702, C703, with the crystal oscillator, Y701. Resistor R704, C704, and U702 make up the reset circuit. The microcontroller is reset if the supply voltage to it dro

35、ps below 4.3 Vdc. Memory The memory section consists of U701, a non-volatile Electrically Erasable and Programmable Read Only Memory (EEPROM). The EEPROM stores the mapping of the compatible groups and channels with respect to rotary switch positions. The microcontroller serially communicates with t

36、he memory via data and clock lines to read the frequency corresponding to the group and channel position. Write to the memory only occurs during factory pro- gramming. During normal usage, this memory is used as a look-up table only. Resistors R702 and R703 allow in-circuit programming of the U701 E

37、EPROM by letting data and clock lines be driven independently of the microcontroller port pin states. R701 is the pull-up resistor for the data line. Audio / Rf Interface The OUT ENAB signal gives the microcontroller the ability to mute the audio during turn on and off, and frequency changes. The mi

38、crocontroller sets the phase-lock loop (PLL) to the required signal using the DATA signal (U703, pin 12) to send the frequency initiali- zation and set-up data. This data is clocked into the PLL by the micro- controller through the CLOCK signal (U703, pin 12) and the Load Enable (LE) signal (U703, p

39、in 10). The LE signal loads the clocked data into a PLLs internal registers to initialize and set the frequency. Shure UC4 Diversity Receiver Parts Designations725C1045 (TK) Rotary Switches for Frequency Selection A 10-position group switch (S701) and a 16-position channel switch (S702) select the r

40、eceiver frequency. The current position of these switches is displayed on the 7-segment LED display. Both rotary switches share the same U703 microcontroller port pins (3 through 6) for a multiplexed switch read operation. The individual switches are selected by pins 7 and 8 of the U703 microcontrol

41、ler. Resistors R705 through R708 are the pull-ups for switch position read. Dual diodes D701 through D704 isolate the switches dur- ing multiplexed read operation. The multiplexed scheme to read switches does not allow switch change detection based on interrupts. Also, the switches cannot be constan

42、tly scanned to determine changes because the scanning fre- quency is in audio range, which makes it hard to filter out. In a steady state, the switch common pins are inputs to pins 7 and 8 of the U703 microcontroller, while pins 3 through 6 of the microcontroller are outputs In this state, pins 4, 5

43、, and 6 are held low which pin 3 is held high. This forces the logic high level on switch common pins if the switches are set on odd positions. For even position settings, the contact on pin 1 is open from the switch common pin, and the internal pull-down resistors force logic low to the U703 microc

44、ontroller, pins 7 and 8. Any switch change is done by state toggle from odd to even, or vice versa. Only this change is detected and followed by a multiplexed switch read. In this case, U703 microcontroller pins 7 and 8 selectively become grounded outputs to read the selected switchs state on pins 3

45、 through 6. A multiplexed switch read is preceded by an audio mute. The receiver audio is muted to allow a quiet change to another frequency. Power Switch Interface When a receiver is switched off, the MT signal goes to logic low on U703, pin 19. This interrupts the microcontroller to immediately mu

46、te the audio so that the receiver turns off without any audio pop. Shure UC4 Diversity Receiver 8Parts Designations25C1045 (TK) Notes This page intentionally left blank. Shure UC4 Diversity Receiver Parts Designations925C1045 (TK) Functional Test Verify operation and reported malfunction, referring

47、to the product Users Guide for a description of the unit as well as information on its operation, troubleshooting, and technical data. Disassembly and Assembly ! CAUTION ! Observe precautions when handling this static-sensitive device. Disassembly Top Cover Removal 1.Remove two screws and washers ea

48、ch from the top, left, and right sides of the receiver (6 screws). 2.Slide the top cover off of the receiver to expose the circuit boards. Front Panel Removal 1.Pull up on the top two tabs to partially release the front panel from the chassis. 2.With a thin tool and the unit upside down, pry the fro

49、nt panel away from the chassis at the two slots located on the bottom of the front panel. 3.With the front panel disengaged from the chassis, carefully pull the front panel away from the chassis. Printed Circuit Board Removal 1.Pull the power knob off the power switch. 2.Disengage the front four standoffs from the chassis by pinching the standoff ends, which will free the front circuit board. 3.Except for the dc power receptacle, remove all screws, nuts, and washers from the back of the unit. 4.Unplug the connector between the dc power receptacle and the circuit board. 5.Remove the